When one mic input is enough
The US-1x2HR is the smallest member of the Tascam US-HR series of high-resolution USB audio interfaces. It has one mic and one instrument input and is therefore particularly suitable for simple and intuitive guitar/vocal recording with a computer. The included loopback function and support for Open Broadcaster Software (OBS Studio), however, makes it also an excellent choice for podcast creation and live streaming. Last but not least, it is a perfect solution for feeding an amplifier system with music from a computer in high quality, for example for a birthday party.
Lower noise and distortion – better sound than ever
The compact US-1x2HR incorporates a wealth of features, including high audio resolution up to 24-bit/192 kHz, ultra-low latency with a Windows buffer size starting at four samples, Ultra-HDDA mic preamplifiers with 48-volt phantom power for superior sound quality with ultra-low noise, a robust USB Type C connector, and a rich assortment of included software to start producing audio right away. The lightweight interface is ideal for mobile recording and production using an iPhone or iPad* with the included Cubasis LE so you can take it to your practice room, use it to report from a live event, or capture nature sounds outdoors.
Usability is key
All US-HR models offer a unique dye-cast aluminum honeycomb structure on the side panels with a slight upward tilt. This design not only results in a sleek, eye-catching design, it also provides just the right amount of weight so the interface won’t move when cables are connected or disconnected. Equally important, the upward tilt offers the ergonomic benefit of being angled in such a way as to make the interface easy to work with.
If you need an uncluttered, easy-to-use audio interface with two inputs and two outputs, very low noise, low distortion and superb sound quality, the Tascam US-1x2HR can be your reliable partner for many years.
* An optional battery pack or AC adapter is required when used with an iPhone or iPad.
Vocal/Instrument Recording With Outstanding Performance
A recording environment with low noise and great audio performance is a relevant factor for vocal and, in particular, wind instruments. The US-1x2HR features an Ultra-HDDA microphone preamplifier with a very low noise level that makes this interface the ideal tool for recording with a condenser microphone. You can also plug in your electric guitar or bass directly using the line/instrument input and use plug-in effects on your computer recording (DAW) software. Or connect any instrument or hi-fi amplifier’s line output to the line input.
The US-1x2HR is also a great tool on the road: Combine it with an iPad and you can capture nature sounds, stream interviews from live events, or simply record your ideas with high quality wherever you go.
Even if you’re not so familiar with recording equipment, the US-1x2HR’s user-friendly design enables you to use it right away.
-Ultra-HDDA mic preamp
-Equivalent input noise: –128 dBu
-Very high S/N ratio of 110 dB (mic to computer)
-Very little distortion: 0.0013%
-Separate inputs for mic and instrument or line level sources
-Separate controls for line and headphones output
-Zero-latency monitoring (can be set to mono or stereo)
Perfect For Music Playback From Your Computer
The US-1x2HR can improve your sound when playing music from your computer. No matter if you create your own dance music using software synths and other plug-ins or if you are the DJ on a birthday party – with its high audio quality and separate controls for headphones and line outputs (loudspeakers) the US-1x2HR easily turns your computer into a perfect-sounding playback device.
You may have noticed that your sound system is not very loud when powered directly from a computer. When using the US-1x2HR to feed your power amplifiers, its high line output level ensures you get the maximum power out of your sound system.
-Maximum line output level of +6 dBV is enough for any power amp
-Standard 6.3-mm headphones output for monitoring
Support for iPads and other iOS devices
Instead of a computer, you can also use an iPad or iPhone together with the US-1x2HR to make music. Performance has been tested with not only the bundled digital audio workstation (Cubasis LE3), but also with other popular recording software – you can continue to use them even if you change DAW software.
-Connect with an iPad or iPhone
-Tested with many popular DAW applications
Ideal for Podcasts and Live Streaming
The Settings Panel, which is installed on your computer, comes with a variety of functions. You can choose whether direct monitoring is done in mono or stereo and adjust the balance between input and computer signals. You can also switch the hardware inputs on and off individually and set the Windows buffer size according to your working environment.
For online broadcasting, Internet communication and other live streaming applications, the US-HR series interfaces offer a Loopback function which can merge input signals 1/2 with signals 1/2 coming from the computer (each can be set to mono or stereo) and send that mix to the broadcasting or other software on the computer. A software slider allows to adjust the final “broadcast” volume independently from the unit’s line output level setting.
-Inputs can be set on/off individually
-Buffer size can be set to a value between 4 and 2048 samples (Windows only)
-Loopback can be set on/off, and each of the merged signal pairs can be switched mono/stereo
-Slider for setting the Loopback master level (broadcast volume)
General
Sampling frequencies
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
Quantization bit depth
24 bits
Analogue audio inputs
Mic input (balanced, IN1)
XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Mic Input impedance
2.4 k Ohms
Mic Nominal input level (gain knob at max.)
-65 dBu (0.0004 Vrms)
Mic Nominal input level (gain knob at min.)
-8 dBu (0.0775 Vrms)
Mic Maximum input level
+10 dBu (2.449 Vrms)
Mic Maximum gain
58 dB
Line/instrument input (balanced/unbalanced, IN2)
6.3-mm standard TRS stereo jack
(Tip: HOT, Ring: COLD, Sleeve: GND)
When set to LINE (balanced)
LINE (balanced) Input impedance
10 kOhms
Nominal input level (gain knob at max.)
-41 dBu (0.0069 Vrms)
Nominal input level (gain knob at max.)
+4 dBu (1.228 Vrms)
Maximum input level
+20 dBu (7.75 Vrms)
Maximum gain
45 dB
When set to INST (unbalanced)
Input impedance
=>1 MOhms
Nominal input level (gain knob at max.)
-51 dBV (0.0028 Vrms)
Nominal input level (gain knob at max.)
–6 dBV (0.5015 Vrms)
Maximum input level
+3 dBV (1.4125 Vrms)
Maximum gain
45 dB
Line input L/R (unbalanced)
RCA
L/R (unbalanced) Input impedance
10 kOhms
L/R (unbalanced) Maximum input level
+6 dBV (1.995 Vrms)
Analogue audio outputs
Line output L/R (unbalanced)
RCA
L/R (unbalanced) Output impedance
100 Ohms
L/R (unbalanced) Maximum output level
+6 dBV (1.995 Vrms)
Headphones output
6.3-mm standard stereo jack
Headphones Maximum output power
18 mW + 18 mW or higher
(THD+N 0.1% or less, 32 Ohms)
Other inputs and outputs
USB
4-pin USB C-type
USB Transfer rate
USB 2.0 Hi-speed (480 Mbits/s)
Power supply (DC IN 5V)
USB Micro B type
Audio performance
Mic preamp EIN (equivalent input noise)
-128 dBu or less
(150 Ohms termination, gain knob at max.)
Mic input Frequency response
44.1/48 kHz: 20 Hz – 20 kHz, +0 dB/–0.4 dB (JEITA)
88.2/96 kHz: 20 Hz – 40 kHz, +0 dB/–0.4 dB (JEITA)
Line input Frequency response
44.1/48 kHz: 20 Hz – 20 kHz, +0.2 dB/–0,1 dB (JEITA)
88.2/96 kHz: 20 Hz – 40 kHz, +0.2 dB/–0.4 dB (JEITA)
Line output Frequency response
44.1/48 kHz: 20 Hz – 20 kHz, +0.2 dB/–0,1 dB (JEITA)
88.2/96 kHz: 20 Hz – 40 kHz, +0.2 dB/–0.4 dB (JEITA)
Mic input to computer S/N ratio
109 dB
(gain knob at minimum, 20-kHz LPF, A-weighted)
Line input to computer S/N ratio
105 dB
(gain knob at minimum, 20-kHz LPF, A-weighted)
Computer to line output S/N ratio
110 dB
(MONITOR knob at maximum, 20-kHz LPF, A-weighted)
Mic input to computer Distortion (THD+N)
0.0013 %
(gain knob at minimum, –5 dBFS input level, 1-kHz sine wave, 20-kHz LPF)
Line input to computer Distortion (THD+N)
0.0027 %
(gain knob at minimum, –5 dBFS input level, 1-kHz sine wave, 20-kHz LPF)
Computer to line output Distortion (THD+N)
0.0015 %
(MONITOR knob at maximum, –4 dBFS input level, 1-kHz sine wave, 20-kHz LPF)
Crosstalk
95 dB or more
(mic/line input to line output, 1-kHz sine wave, gain knob at minimum)
Host computer requirements
Windows
Windows-compatible computer with a USB 2.0 port
2 GHz or faster dual core processor (x86)
2 GB or more memory
Supported audio drivers: ASIO 2.0, WDM
Mac
Mac with a USB 2.0 port
2 GHz or faster dual core processor
2 GB or more memory
Supported audio driver: Core Audio
iOS device
iOS device running iOS 7 or later
Supported audio driver: Core Audio
Power supply
Used with a computer
USB bus power
Used with an iOS device
USB power adapter (that can supply 5 V and a current of at least 700 mA)
External battery pack (that can supply 5 V and a current of at least 700 mA)
Power consumption
1.8 W
Other
Dimensions (W x H x D, without protrusions)
146 mm x 55 mm x 120 mm
Weight
623 g
Operating temperature range
5–35 °C
As an international traveller you are entitled to bring a certain amount/value of goods that are free of Customs duty and exempt Goods and Services tax (GST) into New Zealand. This is called your duty free allowance and personal goods concession. It is important to review these for any purchases you make on The Mall.
Your duty free allowance entitles you to bring into New Zealand the following quantities of alcohol products free of customs duty and GST provided you are over 17 years of age. You do need to be 18 years or over to purchase.
- Up to six bottles (4.5 litres) of wine, champagne, port or sherry or
- Up to twelve cans (4.5 litres) of beer
- And three bottles (or other containers) each containing not more than 1125ml of spirits, liqueur, or other spirituous beverages
Goods other than alcohol and tobacco, whether purchased overseas or purchased duty free in New Zealand, that have a combined total value not exceeding NZ$700 may also be brought as part of your personal goods concession.
When travelling overseas there are legal limits on the amount of duty free alcohol and other goods you can take with you. These amounts will vary depending on the country you are flying into. We always recommend you check the latest limits and exemptions.
Your order can be picked up at an Auckland Airport Collection Point. There is one in departures and one at arrivals in the international terminal. Alternatively, if you are arriving between 11pm and 6am you will be able to collect your order from our lockers. See map
Please bring your order confirmation email and your passport. If you are collecting from lockers you will have been sent an email with your access code, be sure to have this on you in order to collect your order.
If you’re departing Auckland Airport, we recommend that you come to the Auckland Airport Collection Point at least 60 minutes before your flight. If you miss your pickup time or your flight details have changed please let us know as soon as possible.
When you collect your order you will have the opportunity to inspect the items and sign for them.
If you need to return an item, our Collection Point team are there to help you. If you are collecting after hours please return the item to your locker and our team will be in touch as soon as possible. You may also like to view our Returns & refunds which provides information on how this works and outlines the individual retailer's returns and refunds policies.
After Hours Collections
If your order needs to be collected after the Auckland Airport Collection Point desk is closed, your order will be placed in the lockers next to the desk. All the details you will need to collect your order will be provided in your Order Confirmation and Ready to Collect Email.