G3 Starter Kit Pro Starter kit that provides complete entry and exit control for a single door with two readers and Apple Touch Pass support. - (1) Door Hub- (1) G3 Reader Pro- (1) G3 Reader for door exit, or entry for an additional door (second Hub required)- (2) Pocket Keyfobs
- Dimensions
- 174.9 x 126 x 32.9 mm (6.9 x 5 x 1.3")
- Weight
- 363 g (12.8 oz)
- Enclosure material
- Polycarbonate
- Mounting material
- Polycarbonate
- Networking interface
- (5) 10/100/1000 Base-T
- Power method
- PoE++
- UL 294 Power-limited Class 2 PSU
- UL 60950-1/62368-1 LPS/PS2 PSU
- Max. power consumption
- Without PoE output: 30W
- With PoE output: 50W
- PoE input
- 50V DC, 1A
- PoE output
- PoE passthrough, (4) PoE, 50V DC, total 20W
- LEDs
- White/blue
- Button
- (1) Factory-reset
- Digital input
- Request to exit/request to enter/remote release/door position sensor
- Dry output relay
- Lock: 30V DC, 1A
- Aux: 30V DC, 1A
- Powered output relay
- Lock: 12V DC, 1A
- Aux: 12V DC, 0.33A
- 12V DC, 0.33A
- Operating environment
- Indoor use only
- Ambient operating temperature
- 0 to 40° C (32 to 104° F)
- Ambient operating humidity
- 5 to 95% noncondensing
- CAN/ULC-60839-11-1 Grade
- Grade assignment: 1
- Certifications
- CE, FCC, IC, UL 294, CAN/ULC-60839-11-1
- Dimensions
- 160 x 40.4 x 40.55 mm (6.3 x 1.59 x 1.6")
- Weight
- 136 g (4.8 oz)
- Enclosure material
- Polycarbonate, glass
- Mount material
- Aluminum alloy
- Mounting
- Wall mount (Included)
- Gangbox mount (Included)
- Angle mount (Optional)
- Junction box (Optional)
- Weatherproofing
- IP55
- Networking interface
- (1) GbE RJ45 port
- Connectivity
- BLE 4.2
- NFC
- Power method
- PoE
- UL 294 Power-limited Class 2 PSU
- UL 60950-1/62368-1 LPS/PS2 PSU
- Supported voltage range
- 48V DC
- Max. power consumption
- 6W
- ESD/EMP protection
- Air: ±15kV, contact: ±8kV
- Sensor
- Proximity sensor
- Camera view angle
- H: 96.67°, V: 123.15°, D: 153.11°
- Microphone
- Yes
- Speaker
- (1) 4 ohm, 1.5W
- LEDs
- R/G/B/W/Amber
- Button (1)
- Factory-reset
- NFC frequency
- 13.56 MHz
- NFC read range
- < 30 mm
- NFC technology
- ISO/IEC 14443A / 14443B / 15693 / 18092 (Ecma 340)
- MIFARE Classic / MIFARE DESFIRE
- Sony FeliCa™ (ID only)
- NFC Forum tags T1T, T2T, T3T, T4T and T5T
- ECP 2.0
- Operating environment
- Outdoor use
- Ambient operating temperature
- Device: -30 to 45° C (-22 to 113° F)
- Display:* -10 to 45° C (14 to 113° F)
- *The display will turn off when the ambient temperature is above/below the display operation temperature, but other functions will remain functional. (Effective after firmware v1.3.28)
- Ambient operating humidity
- 5 to 90% noncondensing
- Software information
- The software version of a product can be checked at https://unifi.ui.com
- UL 294 level
- Destructive attack: Level I
- Line security: Level I
- Endurance: Level I
- Standby power: Level I
- UL 294 statement
- Compliance with IEEE 802.3 specifications was not verified as part of UL 294.
- The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.
- PoE cabling requirements
- Cable 5e cabling is the minimum performance category recommended. The performance category utilized should match the transmission speed required at the installation site.
- The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 26 AWG (0.13 mm 2 ) for patch cords; 24 AWG (0.21 mm 2 ) for horizontal or riser cable.
- CAN/ULC-60839-11-1
- Grade Grade assignment: I
- Certifications
- CE, FCC, IC, UL 294, CAN/ULC-60839-11-1
- System
- Steady blue: Adopted/device is ready
- Steady white: Pending adoption
- Blinking white/blue: Upgrading firmware
- Strobing red: Emergency lockdown
- Steady orange: Display over or under operation temperature
- Dimensions
- 93 x 40 x 36.5 mm (3.7 x 1.6 x 1.4")
- Weight
- 82 g (2.9 oz)
- Enclosure material
- Polycarbonate, glass
- Mounting material
- Aluminum alloy
- Mounting
- In wall, gang box
- Weatherproofing
- IP55
- Networking interface
- (1) 10/100 MbE RJ45 port
- Connectivity
- BLE 4.1
- NFC
- Power method
- PoE
- UL 294 Power-limited Class 2 PSU
- UL 60950-1/62368-1 LPS/PS2 PSU
- Supported voltage range
- 48V DC
- Max. power consumption
- 5W
- ESD/EMP protection
- Air: ±15kV, contact: ±8kV
- Sensors
- Proximity sensor
- Speaker
- (1) 8 ohm, 0.7W
- LEDs
- R/G/B/W
- Button
- (1) Factory-reset
- NFC frequency
- 13.56 MHz
- NFC read range
- < 30 mm
- NFC technology
- ISO/IEC 14443A / 14443B / 15693 / 18092 (Ecma 340)
- MIFARE Classic / MIFARE DESFIRE
- Sony FeliCa™ (ID only)
- NFC Forum tags T1T, T2T, T3T, T4T and T5T
- ECP 2.0
- Operating environment
- Outdoor use
- Ambient operating temperature
- -30 to 45° C (-22 to 113° F)
- Ambient operating humidity
- 5 to 90% noncondensing
- Software information
- The software version of a product can be checked at https://unifi.ui.com
- UL 294 level
- Destructive attack: Level I
- Line security: Level I
- Endurance: Level I
- Standby power: Level I
- UL 294 statement
- Compliance with IEEE 802.3 specifications was not verified as part of UL 294.
- The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.
- PoE cabling requirements
- Cable 5e cabling is the minimum performance category recommended. The performance category utilized should match the transmission speed required at the installation site.
- The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 26 AWG (0.13 mm 2 ) for patch cords; 24 AWG (0.21 mm 2 ) for horizontal or riser cable.
- CAN/ULC-60839-11-1
- Grade Grade assignment: I
- Certifications
- CE, FCC, IC, UL 294, CAN/ULC-60839-11-1
- Dimensions
- 84 x 39 x 7.4 mm (3.3 x 1.5 x 0.3")
- Weight
- 16 g (0.56 oz)
- Enclosure material
- Polycarbonate, stainless steel, silicone rubber
- Weatherproofing
- IP54
- NFC frequency
- 13.56 MHz
- NFC technology
- ISO/IEC 14443 Type A
- MIFARE DESFire EV3 4K
- UniFi Access Proprietary Security Protocol
- Ambient operating temperature
- -10 to 45° C (14 to 113° F)
- Ambient operating humidity
- 10 to 90% noncondensing
- Certification
- CE
As an international traveller you are entitled to bring a certain amount/value of goods that are free of Customs duty and exempt Goods and Services tax (GST) into New Zealand. This is called your duty free allowance and personal goods concession. It is important to review these for any purchases you make on The Mall.
Your duty free allowance entitles you to bring into New Zealand the following quantities of alcohol products free of customs duty and GST provided you are over 17 years of age. You do need to be 18 years or over to purchase.
- Up to six bottles (4.5 litres) of wine, champagne, port or sherry or
- Up to twelve cans (4.5 litres) of beer
- And three bottles (or other containers) each containing not more than 1125ml of spirits, liqueur, or other spirituous beverages
Goods other than alcohol and tobacco, whether purchased overseas or purchased duty free in New Zealand, that have a combined total value not exceeding NZ$700 may also be brought as part of your personal goods concession.
When travelling overseas there are legal limits on the amount of duty free alcohol and other goods you can take with you. These amounts will vary depending on the country you are flying into. We always recommend you check the latest limits and exemptions.
Your order can be picked up at an Auckland Airport Collection Point. There is one in departures and one at arrivals in the international terminal. Alternatively, if you are arriving between 11pm and 6am you will be able to collect your order from our lockers. See map
Please bring your order confirmation email and your passport. If you are collecting from lockers you will have been sent an email with your access code, be sure to have this on you in order to collect your order.
If you’re departing Auckland Airport, we recommend that you come to the Auckland Airport Collection Point at least 60 minutes before your flight. If you miss your pickup time or your flight details have changed please let us know as soon as possible.
When you collect your order you will have the opportunity to inspect the items and sign for them.
If you need to return an item, our Collection Point team are there to help you. If you are collecting after hours please return the item to your locker and our team will be in touch as soon as possible. You may also like to view our Returns & refunds which provides information on how this works and outlines the individual retailer's returns and refunds policies.
After Hours Collections
If your order needs to be collected after the Auckland Airport Collection Point desk is closed, your order will be placed in the lockers next to the desk. All the details you will need to collect your order will be provided in your Order Confirmation and Ready to Collect Email.